p0402fc3.3c* thru p0402fc36c* 1 05107.r8 8/03 www .protekde vices.com flip chip arra y only one name means protektion? *u.s. patent no. des. d456,367s applica tions ? cellular phones ? mcm boards ? wireless communication circuits ? ir leds ? smart & pcmcia cards iec compa tibility (en61000-4) ? 61000-4-2 (esd): air - 15kv, contact - 8kv ? 61000-4-4 (eft): 40a - 5/50ns fea tures ? esd protection > 25 kilovolts ? available in multiple voltage types ranging from 3.3v to 36v ? 250 watts peak pulse power per line (tp = 8/20s) ? bidirectional configuration & monolithic structure ? protects 1 line mechanical characteristics ? standard eia chip size: 0402 ? weight 0.73 milligrams (approximate) ? flammability rating ul 94v-0 ? 8mm plastic & paper tape and reel per eia standard 481 ? device marking on reel ? top contacts: solder bump 0.004? in height (nominal) 0402 05107 pin configura tion
2 www .protekde vices.com 05107.r8 8/03 p0402fc3.3c* thru p0402fc36c* *u.s. patent no. des. d456,367s device characteristics maximum ratings @ 25c unless otherwise specified operating temperature symbol value -55 c to 150 cc c -55 c to 150 c units t j t stg parameter storage temperature peak pulse power (t p = 8/20s) - see figure 1 p pp 250 watts 0 5 10 15 20 25 30 t - time - s 0 20 40 60 80 100 120 i pp - peak pulse current - % of i pp test waveform parameters t f = 8s t d = 20s t f peak value i pp e -t t d = t i pp /2 figure 2 pulse wave form 0.01 1 10 100 1,000 10,000 t d - pulse duration - s 10 100 1,000 10,000 p pp - peak pulse current - watts figure 1 peak pulse power vs pulse time 250w, 8/20s waveform electrical characteristics per line @ 25c unless otherwise specified pa rt number (see note 1) minimum breakdown voltage @ 1ma v (br) volts maximum clamping voltage (see fig. 2) @ i p = 1a v c volts maximum clamping voltage (see fig. 2) @8/20s v c @ i pp typical capacitance @0v, 1 mhz c pf p0402fc3.3c p0402fc05c p0402fc08c p0402fc12c p0402fc15c p0402fc24c p0402fc36c 3.3 5.0 8.0 12.0 15.0 24.0 36.0 4.0 6.0 8.5 13.3 16.7 26.7 40.0 7.0 9.8 13.4 19.0 24.0 43.0 64.0 12.5v @ 20a 14.7v @ 17a 19.2v @ 13a 29.7v @ 9.0a 35.7v @ 7.0a 55.0v @ 5.0a 84.0v @ 3.0a 150 100 75 50 40 30 25 maximum leakage current (see note 2) @v wm i d a 75* 10** 10*** 1 1 1 1 rated stand-off voltage v wm volts note 1: all devices are bidirectional. electrical characteristics apply in both directions. note 2: *maximum leakage current < 5a @ 2.8v. **maximum leakage current <500na @ 3.3v. ***maximum leakage current <200na @ 5v.
3 www .protekde vices.com 05107.r8 8/03 p0402fc3.3c* thru p0402fc24c* *u.s. patent no. des. d456,367s graphs 0 5 10 15 20 v c - clamping voltage - volts 0 4 8 12 14 figure 6 typical clamping voltage vs peak pulse current for p0402fc05c 10 6 2 i pp - peak pulse current - amps 225c 5-10 sec instantaneous to 200c soldering time cool down time 1-2 minutes to 150c 1-2 minutes to 25c pre-heat time 100c 200c note: this reflow profile does not take into account the printed circuit board (pcb) material heating time. additional time may be required for the preheat time and cool down time upon the pcb or board material. 0 25 50 75 100 125 150 t l - lead temperature - c 20 40 60 80 100 % of rated power peak pulse power 8/20s average power figure 3 power derating curve 0 figure 4 reflow solder profile esd test pulse - 25 kilovolt, 1/30ns (waveshape) figure 5 overshoot & clamping voltage for p0402fc05c 5 volts per division -5 5 15 25 35
4 www .protekde vices.com 05107.r8 8/03 p0402fc3.3c* thru p0402fc36c* *u.s. patent no. des. d456,367s package outline & dimensions copyright ? protek devices 2003 specifications: protek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except jedec). design changes: protek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer?s and that in furnishing engineering and technical assistance, protek assumes no responsibility with respect to the selection or specifications of such products. protek devices 2929 south fair lane, tempe, az 85282 tel: 602-431-8101 fax: 602-431-2288 e-mail: sales@protekdevices.com web site: www .protekde vices .com tape & reel ordering nomenclature 1. surface mount product is taped and reeled in accordance with eia 481. 2. 8mm plastic tape: 7 inch reels - 5,000 pieces per reel. ordering suffix: -t75-1 (i.e., p0402fc05c-t75-1). 3. 8mm paper tape: 7 inch reels -10,000 pieces per reel. ordering suffix: -t710-2 (i.e., p0402fc05c-t710-2). a b c d e f g h i 0.46 nom 0.86 nom 0.99 0.0254 0.10 nom 0.35 nom 0.483 0.0254 0.20 nom 0.127 max 0.076 min 0.406 nom 0.018 nom 0.034 nom 0.039 0.001 0.004 nom 0.014 nom 0.019 0.001 0.008 nom 0.005 max 0.003 min 0.016 nom dim millimeters inches package dimensions notes: 1. controlling dimensions in inches. 2. decimal tolerances for mounting pad and outline: .xxx 0.05mm ( 0.002 ? ). 3. maximum chip size: 1.02 (0.040 ? ) by 0.51(0.020 ? ). package outline 0402 mounting pad note: 1. preferred: using 0.1mm (0.004 ? ) stencil. a b c d e f g h i 0.23 0.48 0.69 0.46 0.99 0.20 0.20 0.66 0.13 0.009 0.019 0.027 0.018 0.039 0.008 0.008 0.026 0.005 dim millimeters inches pad dimensions note: 1. top view of tape. metal contacts are face down in tape package. tape & reel orientation single die - 0402 outline & dimensions: rev 3 - 11/02, 06001 g d h e f i side a b c top end b c solder bump a h d i solder print diameter 0.010? - 0.012? f g die e solder pad
|
